F18 Quick Start-Up for F/A-18C Hornet Checklist

DCS: F/A-18C Hornet

F18 Quick Start-Up

created by myrkrhrafn

Quick Startup

Pre-Start-Up

Set Ejection Seat Lever

DOWN & ARMED

Set Harness Lever

FWD

Parking Brake Lever

ENGAGED

Battery Switch

ON [Right Click]

Start-Up

APU switch

ON (FWD) [Left click]

Engine Crank switch

R (RIGHT) [right-click]

Wait till Right Engine RPM reaches 25 %

Right Throttle to IDLE

[RSHIFT+HOME]

Wait for Right Engine RPM to stabilize around 60-65 % RPM.

Reset MASTER CAUTION

Press Master Caution

Power Left and Right DDIs

DDI knobs to DAY [right click]

Turn on AMPCD

Brightness knob to the right

Power Heads-Up Display

Turn HUD brightness control lever right

BLK LVL

right

RDR

Set to ALT

ATT

Set to AUTO

Bleed Air Switch

360 degrees clockwise from NORMAL back to NORMAL [Right-Click multiple times]

CANOPY

Right DDI

TO HSI

INS Selector

GND (IF ON GROUND)

Start-Up

INS Selector

CV (IF ON CARRIER)

Use Stored Heading

STD HDG (Right DDI)

Wait for OK next to GRND - QUAL on the HSI

INS Selector

IFA (if mission 1986 or later)

INS Selector

NAV (if mission is pre 1986)

MASTER CAUTION

Press twice

FCS RESET

Press

Engine Crank switch

L (LEFT) [left-click]

Wait till Left Engine RPM reaches 25 %

Left Throttle to IDLE

[RALT+HOME]

Wait for Left Engine RPM to stabilize around 60-65 % RPM.

Set OBOGS

HOOK BYPASS

FIELD (IF ON GROUND)

HOOK BYPASS

CARRIER (IF ON CARRIER)

FLAPS

HALF

ANTI-SKID

ON (IF ON GROUND)

ANTI-SKID

OFF (IF ON CARRIER)

RADAR

OPERATE.

T/O TRIM

Press

PITOT HEAT

AUTO

Left DDI

HUD

Right DDI

FCS

Start-Up

Radar Altimeter

200 (ON GROUND)

Radar Altimeter

80 (IF ON CARRIER)

BINGO FUEL

8000

ALR-67 PWR

ECM selector

STBY

DISPENSER

ON (or BYPASS for manual)

IFF

Press and hold till on

When « XP » is displayed, the IFF has been powered up correctly. Verify that Mode 4A is selected (« : » means selected). If 4A is not selected, press OSB (Option Select Button) next to « 4A ».

Link-16 Datalink

Power Up Link-16 Datalink system by pressing the D/L Button a first time to display the Link-4 datalink options, then press the D/L Button a second time to display the Link-16 datalink options. Then, hold the ON button on the UFC for a few seconds. When « ON » is displayed, the Link-16 Datalink system has been powered up correctly.

On UFC, set Link 16 desired Datalink Frequency by entering it on the scratchpad, then pressing « ENT ». 127 is used by default, you can keep it.

Verify on MIDS SUPT page that Datalink information is correct (Network, AIC, F/F, Voice frequencies).

HMD

BRT

STROBE

POSITION LIGHTS

BRT

FORMATION LIGHTS

BRT

LANDING/TAXI

ON (UP) (if needed)

Parking Brake lever

disengage [left click]

Remove Chocks (if on carrier)

[Ground Crew]

Take Off Prep

WINGS FOLD lever

SPREAD

Kneeboard.live

Home

All Checklists

Featured Aircraft:

F-14 Tomcat

F-4E Phantom II

Login

Register

Discord

Donate